Electrolux Feeder 6676 Not Working? Try This [2026]

Quick Fix Summary

The fastest fix for most Electrolux pet camera feeder Model 6676 issues is to power cycle the unit, reconnect it to a 2.4 GHz Wi-Fi network, and clear any jammed kibble from the portion wheel and chute. In many cases, updating firmware in the app and recalibrating portion size restores reliable feeding and camera streaming.

Step-by-Step Troubleshooting

Before you begin

Unplug the feeder, place it on a stable, dry surface, and keep dry kibble within the recommended size range (typically 6-12 mm). The Model 6676 commonly includes a 3 L hopper, a 1080p camera with IR night vision, a 12 V 2 A DC power adapter (barrel connector, center-positive), and 2.4 GHz Wi-Fi support via the companion app. If your unit differs, check the printed manual or the app help screen.

Status lights and sounds (typical)

• Solid blue: Online and connected.
• Blinking blue: Pairing mode.
• Solid red: Feed jam or motor fault.
• Blinking red: Low food or lid open (depends on configuration).
• Soft click at night: IR cut filter switching for night vision.

Step-by-step fixes

1. Power cycle and soft reset. Unplug the power adapter from the wall and the feeder. Wait 30 seconds, then reconnect firmly. If the app still cannot see the device, press and hold the reset pinhole button (usually on the rear or base) for 8-10 seconds until the status LED blinks blue. This clears temporary faults without erasing schedules.
2. Verify power and cabling. Confirm you are using a 12 V 2 A center-positive adapter with a snug 5.5 x 2.1 mm barrel plug. Try a different outlet and inspect the cable for kinks or frayed sections. A weak adapter can cause the motor to stall and the camera to drop. If the adapter feels hot or the LED flickers under load, replace the adapter.
3. Check Wi-Fi fundamentals. The Model 6676 pairs only on 2.4 GHz. Temporarily disable 5 GHz on your router during pairing or run separate SSIDs for 2.4 and 5 GHz. Use WPA2-Personal, avoid enterprise networks, and ensure the SSID and password have standard ASCII characters. Place the router within 10-20 ft of the feeder or use a 2.4 GHz extender. Target an RSSI of -65 dBm or better; if worse, relocate the feeder or router. Prefer channels 1, 6, or 11 to avoid interference.
4. Re-pair in the app cleanly. In your phone settings, grant Bluetooth, location, and local network permissions to the feeder app. Force-close and clear the app cache, then reopen. Put the feeder into pairing mode (reset until blinking blue) and follow the app instructions. If using QR or Bluetooth pairing, keep the phone within 1 ft of the feeder and avoid strong backlighting on the camera during setup.
5. Clear feed jams in the portion wheel and chute. Open the hopper lid and remove the food. Lift out the portion wheel or impeller (refer to your manual; some wheels have a locking tab). Vacuum crumbs from the hopper throat, wheel cavity, and chute. Inspect for swollen or oily kibble, which tends to clump. Replace with dry, uniform kibble within 6-12 mm size. Spin the motor coupling by hand to feel for binding. Reinstall the wheel fully seated to avoid misalignment.
6. Manage moisture and seals. Moisture causes clumping and sensor errors. Replace the desiccant pack in the lid compartment if included, and inspect the lid gasket for cracks or gaps. Wipe the chute with a dry cloth and allow all parts to air dry before refilling. Never use wet food or sticky treats in the hopper. If humidity is high, store kibble in a sealed container and refill small amounts more frequently.
7. Calibrate portion size and run test feeds. In the app, open feeding settings and run 3 manual test feeds into a bowl. Weigh the output to verify grams per portion. Adjust the portion calibration until the measured output matches your target. Enable anti-jam and slow-feed options if available. Ensure your phone and feeder show the correct timezone and synchronized time; schedule drift can cause missed feeds.
8. Restore camera clarity and night vision. Clean the lens cover with a microfiber cloth. Confirm the privacy shutter (if present) is fully open. In the app, toggle night mode and watch for the IR LEDs to glow faintly red. Eliminate reflective surfaces directly opposite the camera to reduce glare. Grant microphone permission for two-way audio and adjust speaker volume in the app. If the stream buffers, reduce resolution from 1080p to 720p and check Wi-Fi signal quality.
9. Update firmware and app. Firmware updates fix feed motor timing, camera stability, and Wi-Fi bugs. In the app, check for device firmware updates and apply with the feeder on reliable power and Wi-Fi. Also update the app itself via your app store. After updating, reboot the feeder and run a test feed and a short camera session.
10. Factory reset (last resort) and re-add. If issues persist, perform a full factory reset: press and hold the reset pinhole for 15 seconds until the LED cycles, then release. Re-add the device in the app, rename it, and re-enter schedules. Reconfirm Wi-Fi settings, timezone, and notifications. Test feeding and camera streaming before refilling the hopper.

Common symptoms and targeted fixes

• Missed feeds: Check jammed wheel, portion calibration, and schedule time sync.
• Overfeeding: Recalibrate grams per portion and verify wheel seating.
• Camera offline: Re-pair on 2.4 GHz, reduce stream resolution, and update firmware.
• Night vision poor: Clean lens, remove reflective objects, confirm IR LEDs engage.
• Loud motor noise: Inspect for wheel misalignment or debris in the chute.

Replacement Parts

If inspection reveals damage or excessive wear, replace the affected parts. Use genuine or compatible items that match voltage, dimensions, and material. You can search for parts using this link: https://www.amazon.com/s?k=Electrolux+pet+camera+feeder+Model+6676&tag=manuallogic-20

• 12 V 2 A DC power adapter (5.5 x 2.1 mm, center-positive): Resolves power instability and motor stalling.
• Portion wheel / impeller kit: Fixes jams from worn fins or warped plastic that mis-feeds kibble.
• Hopper lid gasket: Restores an airtight seal to reduce moisture and clumping.
• Desiccant silica gel pack: Maintains dry conditions in the hopper for reliable dispensing.
• Chute infrared sensor pair: Replaces faulty sensors that mis-detect feed flow or jams.
• Feed button micro switch: Repairs non-responsive manual feed button presses.
• Internal 2.4 GHz Wi-Fi antenna: Improves weak signal issues when original antenna is damaged.
• Camera lens cover and IR LED board: Restores image clarity and night vision if components are cracked or burnt out.
• Stainless steel bowl insert: Prevents odors and helps kibble slide cleanly into the bowl.
• Optional battery backup pack (if supported): Keeps schedules during brief outages; verify compatibility with Model 6676 before purchase.

After installing any replacement part, run a full diagnostic: power cycle, verify Wi-Fi, perform 3 test feeds, and check camera day and night. Keeping kibble dry, maintaining seals, and staying current on firmware are the keys to reliable, jam-free operation of your Electrolux pet camera feeder Model 6676.