Eufy Grill 6163 Not Heating? Try This First [2026]

Quick Fix Summary

If your Eufy electric grill Model 6163 will not heat or cooks unevenly, start with a full power check at a known-good wall outlet, reseat the power cord, set the temperature to max, and allow a proper preheat. Then clean the plates, vents, and drip system to clear grease that can trigger overheat protection or cause smoke. Many issues resolve with these basics, plus a reset of any built-in overheat cutoff if your unit includes one.

Because countertop grills draw high current, avoid power strips and GFCI chains during testing. If breakers trip, the plug warms, or a burning smell appears, stop and investigate before using the grill again.

Step-by-Step Troubleshooting

Before you begin: unplug the grill, let it cool completely, and place it on a dry, stable surface. Consult your user manual for safety warnings specific to your unit. The rating label on the base shows the required voltage and wattage; verify your outlet matches that rating.

1. Verify the outlet and circuit
   

   Plug a lamp or phone charger into the same outlet. If that device fails, reset the wall GFCI and the breaker in your panel. High-wattage grills perform best on a dedicated 15 A circuit. Avoid power strips, long extension cords, and surge protectors; they can cause voltage drop and slow heating. Try a different wall outlet on a separate circuit if the first one is suspect.

2. Inspect and reseat the power cord
   

   Check the cord for cuts, kinks, melted insulation, or prongs that are loose, bent, or discolored. If your 6163 uses a detachable cord, fully remove and firmly reseat it until it is fully home. With the unit off and unplugged, wipe dust from the cord inlet. If the plug or cord becomes warm during use, discontinue use and replace the cord or have the unit serviced.

3. Check controls and indicators
   

   Turn the temperature dial or presets to the highest setting. Close the lid if your model requires lid-closed operation. Look for a power or preheat light. Allow several minutes for preheat; many grills require up to 10 minutes to reach temperature. If the power light never illuminates but the outlet is known good, suspect a faulty switch, indicator lamp, or internal fuse.

4. Reset overheat protection (if present)
   

   Some electric grills include a thermal cutoff that trips when grease blocks airflow or the unit overheats. After the grill is completely cool and unplugged, look on the underside near the rear feet or cord entry for a small recessed button sometimes labeled Reset or O/T. Press gently with a paper clip. If it clicks, it was tripped. Reconnect power and test again. Frequent trips point to insufficient cleaning, blocked vents, or a failing thermostat.

5. Deep clean plates, sensors, and drip path
   

   Built-up grease can cause smoke, hot spots, and premature cycling of overheat protection. Remove the drip tray and empty it. If plates are removable, lift them off per the manual. Wipe plates with a soft sponge and mild dish soap; do not use abrasives or steel wool. Never immerse the main body. Clean around the temperature sensor area and lid hinge where grease often accumulates, then dry thoroughly. Reinstall the plates securely so they sit flush on the heating surfaces.

6. Evaluate heating performance
   

   Preheat the empty grill on high for up to 10 minutes. A quick way to visualize heat distribution is the toast test: place several slices of white bread across the lower plate, close the lid for 60 to 90 seconds, then check browning patterns. Uniform browning suggests normal heat; pale zones indicate a cold area, often an open element path or a loose plate. If one plate heats and the other does not, the non-heating side may have a failed element or sensor.

7. Check for lid or interlock issues
   

   Some grills include a lid-closed switch to prevent heating when open. Gently close the lid and listen for a faint click near the hinge. If the lid does not close squarely, food residue or a misaligned hinge can prevent the switch from engaging. Clean the hinge area and ensure the lid closes evenly. Do not bypass any safety switches; if the interlock is faulty, seek service.

8. Address smoke and odor
   

   Persistent smoke usually comes from residual oils or sugary marinades. Use high smoke point oils, pat foods dry, and avoid excess sauces during searing. Ensure the drip tray is seated fully and not overfilled. If new out of the box, a brief burn-in on high outdoors or under a range hood can clear manufacturing residues. Acrid or electrical odors, melting plastic smells, or visible arcing indicate a serious fault; unplug immediately and inspect the cord, plug, and underside for damage.

9. Resolve tripped GFCI or breaker
   

   If a GFCI trips, moisture may have entered the plates or wiring, or there is a leakage path to ground. Let the grill dry for 24 hours in a warm, low-humidity room. Do not operate outdoors in rain. If the household breaker trips (not just a GFCI), avoid shared circuits with other appliances. Repeated trips with a dry unit point to an internal short or failing element; discontinue use and arrange for repair.

10. Advanced checks (optional and safe)
    

    Only if you are comfortable and the grill is unplugged: gently wiggle the temperature knob while watching the indicator light during a test run; flickering suggests a worn potentiometer or switch. Lightly press on the removable plates during preheat; a loose plate can reduce heat transfer. You can also use a non-contact IR thermometer to verify plate temperatures; large differences between zones suggest an element or sensor fault. Avoid opening the case if doing so would void warranty.

11. When to seek service
    

    If the grill shows no power at a known-good outlet, heats only partially, trips protection repeatedly, or shows signs of electrical damage, contact the manufacturer or a qualified appliance technician. Common service items include thermal fuses, thermostats, heating elements, and control boards. Provide the full model (Eufy electric grill Model 6163) and the serial number from the rating label to speed parts matching.

Usage tips to prevent repeat issues

- Preheat fully before loading food; cold starts encourage sticking and uneven sear.
- Do not overcrowd. Large batches can pull temperature down and cause steaming and excess moisture.
- Empty the drip tray during long cooks to avoid overflow.
- After each session, wipe plates while warm (unplugged) to prevent hardened buildup.

Replacement Parts

When wear or failure requires replacement, choose parts designed for your exact model. Always match by full model number and compare photos and dimensions. If your grill is under warranty, contact the manufacturer first.

• Detachable power cord (match plug type and amperage): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20
• Removable nonstick plate set (upper and lower, model-specific): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20
• Drip tray / grease cup (ensure correct width and latch style): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20
• Temperature knob or selector (if cracked or slipping): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20
• Thermal fuse / cutoff (rated for your grill; professional install recommended): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20
• Heating element assembly (upper or lower plate; model-specific): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20
• Lid hinge kit / interlock switch (if lid does not close or switch fails): https://www.amazon.com/s?k=Eufy+electric+grill+Model+6163&tag=manuallogic-20

Tip: Many generic parts list wattage and plate dimensions. Use your rating label and a quick measurement to verify compatibility before ordering. After any parts replacement, perform a supervised test run on high heat to confirm stable operation before cooking.